Half lengthways, with the wrong sides on the inside. You’ll need two strips up to 78cm long depending on the size you’re making, there will probably be a little leftover to trim off.Fold the two strips of bias binding in Secure the facing to the shoulder seam allowance with a few small hand stitches.įrom dress fabric, make strips of bias binding for your hem. Understitch the facing around the neckline, sewing only through the facing and the seam allowance. Press both the facing and the seam allowance away from the body of the dress. Clip around the neckline curve to allow it to sit flat when turned right side out. Lay the facing right side down on top, matching up the raw edges of the neckline and the shoulder seams. Lay the dress flat, with the right side facing up. Neaten the seam allowances and press the seams open.Neaten the lower edge of the facing with a zig zag stitch or an overlocker. With right sides together, pin the facings at the shoulder seams. If using, apply fusible interfacing to the front and back neck facings. Neaten the seam allowances and press the seams open. With right sides facing, pin the front and back together at the shoulder seams. Pin and sew the bust darts on the front piece. There are different front facings depending whether you’re making the high or V-neck option. Using the cutting guide, cut all the pieces from fabric. Fold and press in 1cm, then another 3cmĪround the base of the sleeves, pin, then edgestitch in place.Trace the pattern from your pattern sheet onto dressmaker’s tissue paper, transferring all the markings. Neaten around the seam allowances of the armhole. Adjust the gathers to fit the armhole of the dress, pin, then sew in place. Pull the gathering threads up slightly, then place the sleeve into the armhole.Ĩ Match the side seams and underarm seam of the sleeve, plus the notch in the centre of the sleeve to the one at the end of the shoulder seam. Press the seams open, then turn the sleeves right sides out. Match, pin and sew the underarm sleeve seams, right sides together. Gathering stitches around the head of the sleeves, starting from the front notch and finishing at the back. Neaten the underarm edges of the sleeves. Trim any excess binding at the centre-back edges, fold back the ends and slip stitch in place by hand.ħ With right sides together, match the side seams, pin and stitch, then press the seams open. Pin, then edgestitch, sandwiching the raw edge of the neckline inside the bias binding. Open one side of the strip, pin it around the neckline, then stitch along the fold line.Ħ Fold the strip over onto the wrong side of the neckline and position the remaining folded edge over the stitching line. Fold and press in 1cm on both long edges of the bias strip or use a bias binding maker. Carefully thread the zip pull through to the right side and close.ĥ Match, pin and stitch each shoulder seam of the front to a back piece, right sides together, then press the seam allowances open. Backstitch, then sew the other side of the zip in place. Teeth to the crease line in the seam allowance.Ĥ Pin and stitch one side of the zip, using a zipper or concealed zipper foot and leaving 3cm of the base unstitched. Fold and press the seam allowance along both sides of the back opening, then open it out and with right sides together, place the opened zip face-down, matching the Pin and edgestitch the pockets onto the front where indicated on the pattern.ģ Pin the two back pieces right sides together, matching the centre-back seam, then sew as far as the zip notch mark from the base of the dress. Press the edges, then continue folding and pressing a 1cm seam along the side edges and base. Trim the bulk from the corners, then turn the top part of the pocket back to the wrong side. Fold over onto the right side of the pocket and stitch down each sideĮdge with a 1cm seam allowance. Neaten the side edges, centre-back edges and shoulders of the front and back pieces.Ģ Fold and press under 1cm, then another 4cm on one of the shorter pocket edges. Stitch the darts into the front dress from the sides to the points, then press them up towards the shoulders. Cut out the pieces according to the cutting guide, then transfer any 1 Download and print the pattern at .uk/templates.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |